Flip compositing node

Flips the image horizontally and/or vertically.

This operation flips the image horizontally and/or vertically.

It can also be used to rotate the image 90º so it flops sideways (X and Y resolutions are switched).

Note

If a flop is being performed, scoping cannot be used.

Parameters

Flip

Flip Horizontal/Vertically	Flips the image in the specified direction.
Flop 90 Degress	Flops the image on its side. This operation cannot be scoped.

Mask

A mask can be chosen to limit the effect of the operator to areas defined by the mask. The mask can be taken from the mask input (side input) or from the first input itself.

Effect Amount

If no mask is present, this blends the output with the input by a constant amount (0 = all input, 1 = all output).

If a mask is present, this amount multiplies the mask.

Operation Mask

Selects the mask plane to use as a mask from the mask input. The mask can be selected from:

A mask can be a component of a plane or an entire plane. If a vector plane is supplied as a mask, its components are multiplied by the images' components.

Scalar Mask ('A', 'C.r')

C.r = I.r * M
C.g = I.g * M
C.b = I.b * M

Vector Mask ('C')

C.r = I.r * M.r
C.g = I.g * M.g
C.b = I.b * M.b

First Input	Useful for masking the operation to the image’s own alpha plane.
Mask Input	Selects the mask from the side mask input.
Off	Turns off masking, without requiring disconnection of the mask input (useful for temporarily disabling the mask).

Resize Mask to Fit Image

If the mask image is a different resolution than the output image, turning on this parameter will scale the mask to the output image’s resolution.

If this node is changing constantly, and the mask is not, it is somewhat faster to put a Scale COP down to do the resize for the mask image. Otherwise, the scale will occur every time this node cooks.

Invert Mask

Inverts the mask so that all fully 'masked' portions become unmasked. This saves you from inserting an Invert COP after the node with the mask.

Scope

Plane Scope

Specifies the scope for both the RGB components of Color, Alpha, and other planes. The (C)RGBA mask only affects Color components and Alpha. 'C' will toggle all the RGB components.

For planes other than Color and Alpha, the plane name (plus component, if applicable) should be specified in the string field. The pulldown menu can be used to select planes or components present in this node.

A plane is specified by its name. A component is specified by both its plane and component name. The '*' wildcard may be used to scope all extra planes. Any number of planes or components can be specified, separated by spaces.

Examples:

P
N.x N.y
P N Pz

Frame Scope

Allows scoping of specific frames in the frame range. This is in addition to the plane scope (so a plane at a certain frame must be both plane scoped and frame scoped to be modified).

All Frames	All frames are scoped.
Inside Range	All frames inside a subrange are scoped.
Outside Range	All frames outside a subrange are scoped.
Even Frames	Even numbered frames are scoped.
Odd Frames	Odd numbered frames are scoped.
Specific Frames	A user-defined list of frames are scoped.

Frame Range

For Inside/Outside range, this parameter specifies the subrange of the sequence to scope (or unscope). This can be edited in Timeline viewer mode ( Ctrl + 2 in viewer).

Frame Dropoff

For Inside/Outside Range, this parameter specifies certain number of frames before and after to slowly ramp up to scoped. The operation will be blended with its input to 'ease in' or 'ease out' the scoping effect over a number of frames. This can be edited in Timeline viewer mode ( Ctrl + 2 in viewer).

Non-scoped Effect

For unscoped frames, this sets the blend factor between the input and modified images. Normally this is zero (use the input image). By setting this to a non-zero value, you can make unscoped frames be 'slightly' unscoped. The value can vary between 0 (unscoped) and 1 (scoped).

Frame List

The frame list for 'Specific Frames'. Frame numbers should be separated by spaces.

Automatically Adjust for Length Changes

If the sequence range changes, enabling this parameter will adjust the subrange and frame dropoff lengths to fit the new range.

Usages in other examples

Example name	Example for